Re: Need a little assistance on Death Race Monitor

You're probably right, the Aerospace division makes all sorts of interesting stuff (but no
longer monitors).

Matt Rossiter wrote:

> Are you sure it's not the same company? The logo on the schematics is exactly the same.
>
> Compare these...
>
> ftp://ftp.rossiters.com/pub/ball.jpg
> http://www.ball.com.
>
> They must have some affliliation wouldn't you think? Hmm...
>
> Matt
>
> Rodger Boots wrote:
>
> > Ball Brothers! They made a damn fine monitor back in those days, used in a lot of
> > computer terminals. (And, no, they are no relation to the canning supplies people,
> > different Ball all together.)
> >
> > Matt Rossiter wrote:
> >
> > > A programmable transistor? I've never heard of that before. The choke coil that
> > > looks like a resistor is new to me too. This monitor has had all kinds of
> > > surprises. Ball Brothers, apparently, is the same company that makes Jars and
> > > lids. I had no idea my mom's homemade Jam would have some relation to my death
> > > race.
> > >
> > > Anyway - I've been getting some suggestions from other people privately as well -
> > > and Q112 seems to be a likely suspect. When I get home I'll get the scope out and
> > > tell you if I'm getting some pulses.
> > >
> > > Thanks!
> > >
> > > Matt
> > >
> > > Rodger Boots wrote:
> > >
> > > > Wow, a PUT (Programmable Unijuction Transistor) oscillator! THAT's something
> > > > you don't see much.
> > > >
> > > > The "base" (actually the gate) of the PUT (Q112) should be narrow sync pulses
> > > > (is any sync is being sent to the monitor) and across the coil (L101) will be a
> > > > 60 Hz pulse or ringing waveform. Neither will probably read anything on a
> > > > meter, you'll need a scope.
> > > >
> > > > If you think the PUT may be bad, it crosses to an NTE6402.
> > > >
> > > > Matt Rossiter wrote:
> > > >
> > > > > I'm a little stuck on a problem here. I'm not getting any vertical
> > > > > deflection. All I get is a thin horizontal line - within that
> > > > > horizontal line, I can see things moving back and forth. I was
> > > > > wondering if someone could look at the schematics here
> > > > > ftp://ftp.rossiters.com/pub/ball-brothers-TG20-23.jpg.
> > > > >
> > > > > The large vertical deflection transistor is fine. If you look on the
> > > > > schematics at the section labelled "vertical oscillator" - at the base
> > > > > of Q112 I'm getting zero volts - plus I'm getting zero volts where the
> > > > > the choke is below it. Shouldn't I be getting some kind of reading
> > > > > around that choke? Just looking for some ideas - I'm not exactly sure
> > > > > what the purpose of that choke coil is.
> > > > >
> > > > > Thanks...
> > > > >
> > > > > Matt
> > > > >
> > > > > ---------------------------------------------------------------------------
> > > > > ** To UNSUBSCRIBE from rasterlist, send a message with "UNSUBSCRIBE" in the
> > > > > ** message body to rasterlist-request@synthcom.com. Please direct other
> > > > > ** questions, comments, or problems to neil@synthcom.com.
> > > >
> > > > ---------------------------------------------------------------------------
> > > > ** To UNSUBSCRIBE from rasterlist, send a message with "UNSUBSCRIBE" in the
> > > > ** message body to rasterlist-request@synthcom.com. Please direct other
> > > > ** questions, comments, or problems to neil@synthcom.com.
> > >
> > > ---------------------------------------------------------------------------
> > > ** To UNSUBSCRIBE from rasterlist, send a message with "UNSUBSCRIBE" in the
> > > ** message body to rasterlist-request@synthcom.com. Please direct other
> > > ** questions, comments, or problems to neil@synthcom.com.
> >
> > ---------------------------------------------------------------------------
> > ** To UNSUBSCRIBE from rasterlist, send a message with "UNSUBSCRIBE" in the
> > ** message body to rasterlist-request@synthcom.com. Please direct other
> > ** questions, comments, or problems to neil@synthcom.com.
>
> ---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from rasterlist, send a message with "UNSUBSCRIBE" in the
> ** message body to rasterlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to neil@synthcom.com.

---------------------------------------------------------------------------
** To UNSUBSCRIBE from rasterlist, send a message with "UNSUBSCRIBE" in the
** message body to rasterlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Thu Jul 12 09:17:00 2001