<x-html>
<html>
<body>
A while ago you asked about this, is it a socket you need or the 40 pin
dip header? I've not seen a socket either...but I guess you could always
solder a socket to a header.<br><br>
Where is the pdf file located?<br><br>
John :-#)#<br><br>
At 03:57 PM 01/04/2003 -0500, Kev wrote:<br><br>
<blockquote type=cite class=cite cite><font face="arial" size=2>Can
anyone source the part that crimps to the ribbon cable & provides a
40 pin dip socket? I could use some of those!</font><br>
<br>
<font face="arial" size=2>Didn't see it in DigiKey, Mouser or
Allied.</font><br>
<br>
<font face="arial" size=2>(40pincclip.pdf has a sketch of the
part)</font><br>
<br>
<font face="arial" size=2>Kev</font><br>
<br>
<dl>
<dd>----- Original Message ----- <br>
<dd>From:</b> <a href="mailto:jrr@flippers.com">John Robertson</a> <br>
<dd>To:</b>
<a href="mailto:techtoolslist@flippers.com">techtoolslist@flippers.com</a> <br>
<dd>Sent:</b> Tuesday, April 01, 2003 2:45 PM<br>
<dd>Subject:</b> Re: Chip clip adapter for 9000<br><br>
<dd>I think you could make something from Digikey's cables and clips. I have a CPU clip I have experimented with (on a CAT Box), but not on the System 80 MPUs with a 6502 Fluke pod. I don't know why, just never did...however you do need to lift the two jumpers to disable the CPU (that's what I did with the CAT Box - oh, I still have one CB for sale if anyone is interested)...it might work, should not harm the CPU...perhaps the next MPU I pull out I'll test this on and let you folks know the results, later this week...<br><br>
<dd>John :-#)#<br><br>
<dd>At 12:45 PM 01/04/2003 -0500, James Bright wrote:<br><br>
<blockquote type=cite class=cite cite><br>
<dd><font face="arial" size=2>Are the clip adapters for the 9000 series pods still around? If I remember correctly, Gottlieb soldered in the CPUs in the sys80 CPU boards. I'm going to start working on some in the next few weeks. Just wondering how hard they are to find and if people have used them with any success. I suppose I could desolder the CPU, but if it's working, I'd rather not.</font><br>
<dd> <br>
<dd><font face="arial" size=2>JB</font><br>
<dd> <br>
<dd><font face="arial" size=2>--James Bright<br>
<dd>www.QuarterArcade.com<br>
<dd>Restored Arcade Games for your Home</font></blockquote><br>
<dd>How to subscribe or unsubscribe from TTL<br><br>
<dd>To do either you send email to "MajorDomo@flippers.com" and in the body you state either "Subscribe techtoolslist" or "Unsubscribe techtoolslist", note that the Subject is "" (Blank)...<br><br>
<dd>FTP site is: ftp://ftp.flippers.com/TTL/ <br>
</dl></blockquote></body>
</html>
</x-html>
Received on Sun May 04 20:46:27 2003
This archive was generated by hypermail 2.1.8 : Tue Dec 02 2003 - 18:40:52 EST