Re: RASTER: FW: Using 8080 pod on Midway 8080 boards (Space Invaders)

Uh-oh.....

Op 22 feb. 2013, om 21:39 heeft John Robertson <jrr@flippers.com> het volgende geschreven:

> David Shoemaker wrote:
>> Any chance I could have you open one up and look at the ground lead on the
>> twisted pin cable? I have an 8085 pod I tried to borrow the twisted pair
>> cable from and it has the shield ground tied to pin 20. That doesn't work
>> on the 8080 as that pin is +5. Ground should be tied to pin 2. I am
>> wondering how they did that I suspect it is in the potted UUT end as I don't
>> see anything on the connector end.
>>
>> David
>>
>>
>
> Hi David,
>
> I've taken these pods apart enough times to tell you this off the top of my head. The twisted pair cable is broken out for one row alternately inside the pod case, one wire goes to a common metal strip, the other to the pin header. The strips are tied together and have a short jumper wire that simply goes to the screw on the left end of the connector.
>
> At the encapsulated end all the grey ground wires appear to be tied together as well as to any ground pins on the plug.
>
> So you can't exchange shielded cables between different pods UNLESS they have the same ground connections on the CPU.
>
> John :-#)#
>>
>> -----Original Message-----
>> From: owner-rasterlist@vectorlist.org
>> [mailto:owner-rasterlist@vectorlist.org] On Behalf Of Alex Yeckley
>> Sent: Wednesday, February 20, 2013 4:15 AM
>> To: 'David Shoemaker'; 'Technical Tools Mail List'; jrr@flippers.com;
>> rasterlist@vectorlist.org
>> Subject: RE: [Techtoolslist] RASTER: FW: Using 8080 pod on Midway 8080
>> boards (Space Invaders)
>>
>>
>>> Do your pods have the twisted cable or the straight? Both mine have the straight.
>>>
>>
>> Our 8080 pods have the OEM twisted cables. Our 6502 pods (re: Clay's
>> Tempest question) come in both twisted and the flat cables. I'm assuming
>> the flat cable is a non-factory replacement item, but could be totally wrong
>> about that. The 6502 pod that failed just happened to have had a flat cable
>> but I'm confident the drive problem was unrelated; we found one specific
>> driver output that wasn't going sufficiently high once plugged into a "real"
>> target board. It wasn't a general malaise of the address lines like you
>> might expect from transmission line losses or higher EMI susceptibility due
>> to the flat cable if that's what you are wondering.
>>
>>
>>> Are you using a 9010 or a 9100 to drive the pod?
>>>
>>
>> Both...
>>
>> Alex
>> ----
>> ayeckley@elektronforge.com
>> www.elektronforge.com
>>
>> ---------------------------------------------------------------------------
>> ** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
>> ** Please direct other questions, comments, or problems to chris@westnet.com
>>
>>
>>
>>
>
>
> --
> John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, VideoGames)
> www.flippers.com "Old pinballers never die, they just flip out"
>
> _______________________________________________
> Techtoolslist mailing list
> Techtoolslist@flippers.com
> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

André Huijts
andre.huijts@upcmail.nl

_______________________________________________
Techtoolslist mailing list
Techtoolslist@flippers.com
http://seven.pairlist.net/mailman/listinfo/techtoolslist
FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
Received on Fri Feb 22 16:21:08 2013