Re: Fluke 9010A Install with FIDE

I think the cable is the issue. I'm running a db9 on the PC end and a db25 on the fluke end. I believe I need pin 7 of the db9 to pin 5 of the db25 as well as pin 8 of the db9 to pin 4 of the db25. These are the request and clear to send and none of these ohm out. I believe these are the handshake. I will try the low baud as suggested.

Thanks

Justin

Sent from my Verizon Wireless 4G LTE DROID

Rodger Boots <rlboots2@gmail.com> wrote:

>Another possible way to help your problem is to decrease the baud rate.
>What typically happens at high baud rates is that data transfers fine until
>you hit a carriage return, then all the data that was just sent has to be
>processed. If the sender keeps going you overrun the character buffer in
>the receiving device. Something as old as a 29A wouldn't handle more than
>2 characters before overflowing. That's where handshaking comes in. But
>if you use hardware handshaking (the best choice at high speeds), the
>device stops the computer from sending until it's ready to go again.
>
>But you can run without any handshaking if the baud rate is low enough.
>
>So if you set the baud rate to something nasty slow (like 1200 or less) and
>the two machines then worked THAT would tell you that handshaking is the
>problem. At least gives a clue.
>
>
>On Fri, Apr 12, 2013 at 9:38 PM, JJ <rugd2go@comcast.net> wrote:
>
>> I tried the prior and all my settings look good. Anyone have the cable
>> pin outs? I would like to ohm out the cable.
>>
>> Thanks
>>
>> Justin
>>
>> Sent from my Verizon Wireless 4G LTE DROID
>>
>> Rodger Boots <rlboots2@gmail.com> wrote:
>>
>> >Flow control is probably off or set wrong on computer end. Open up
>> control
>> >panel, system, hardware, com ports. Selects your com port and port
>> >settings. Flow control should be XON/XOFF for software flow control or
>> >Hardware for hardware flow control. Use whichever matches the programmer
>> >setup.
>> >
>> >If you're using Hardware and it doesn't work your null modem cable may be
>> >wired wrong.
>> >
>> >Good luck.
>> >
>> >
>> >On Fri, Apr 12, 2013 at 5:36 PM, JJ <rugd2go@comcast.net> wrote:
>> >
>> >> I tried to connect to my 9010a and laptop using xp and received a buffer
>> >> overrun or overflow message on the 9010. Any ideas on what the cause
>> might
>> >> be? I was using a null cable.
>> >>
>> >> Justin
>> >>
>> >> Sent from my Verizon Wireless 4G LTE DROID
>> >>
>> >> Matthew Rossiter <matt@rossiters.com> wrote:
>> >>
>> >> >Has anyone gotten Fluke FIDE to work in Windows 7? I've always just
>> >> >used my old Win XP laptop with a USB/Serial adapter and it works great.
>> >> >
>> >> >On 4/12/2013 11:13 AM, Theron Troxel wrote:
>> >> >>
>> >> >> I found out what I was doing wrong. Didn't have a null modem cable
>> >> adapter. Ended up ordering a serial cable adapter, which I knew I
>> didn't
>> >> want. Will try again with the correct part.
>> >> >>
>> >> >> ________________________________
>> >> >> From: Theron Troxel <troxelone@yahoo.com>
>> >> >> To: Technical Tools Mail List <techtoolslist@flippers.com>
>> >> >> Sent: Friday, April 12, 2013 1:07 PM
>> >> >> Subject: Re: [Techtoolslist] Fluke 9010A Install with FIDE
>> >> >>
>> >> >>
>> >> >>
>> >> >>
>> >> >>
>> >> >> ________________________________
>> >> >> From: Theron Troxel <troxelone@yahoo.com>
>> >> >> To: "techtoolslist@flippers.com" <techtoolslist@flippers.com>
>> >> >> Sent: Monday, April 1, 2013 5:50 PM
>> >> >> Subject: [Techtoolslist] Fluke 9010A Install with FIDE
>> >> >>
>> >> >> Trying to get my fluke to respond to my computer. I have a
>> USB-to-RS232
>> >> cord, and my computer recognize the cord. I went to settings on my
>> computer
>> >> and set it to com1 and matched everything to the computer and fluke.
>> >> >>
>> >> >> Wrote a simple program that just displays "test" and tried sending it
>> >> through the Fluke FIDE software. The fluke never responds to when I send
>> >> the program. I don't get any errors of any type on the fluke. However,
>> on
>> >> the Fluke FIDE I get the following error:
>> >> >>
>> >> >>
>> >> >> Starting process...
>> >> >> WARNING: Include file already exists. File may have been included
>> >> >> multiple times, or two files with the exact same file name may exist.
>> >> >> It is recommended that you give your files distictive file names.
>> >> >> C:\Program Files (x86)\Fluke FIDE\Scripts\test.9lc -> C:\Program
>> Files
>> >> (x86)\Fluke FIDE\Internal\test.9lc (exists).
>> >> >> ERROR: Could not create batch file C:\Program Files (x86)\Fluke
>> >> FIDE\Internal\9lc.bat.
>> >> >> Permission denied
>> >> >> Batch
>> >> >> file processing failed.
>> >> >> _______________________________________________
>> >> >> Techtoolslist mailing list
>> >> >> Techtoolslist@flippers.com
>> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> >> >> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>> >> >> _______________________________________________
>> >> >> Techtoolslist mailing list
>> >> >> Techtoolslist@flippers.com
>> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> >> >> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>> >> >> _______________________________________________
>> >> >> Techtoolslist mailing list
>> >> >> Techtoolslist@flippers.com
>> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> >> >> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>> >> >
>> >> >_______________________________________________
>> >> >Techtoolslist mailing list
>> >> >Techtoolslist@flippers.com
>> >> >http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> >> >FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> >> >Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>> >> _______________________________________________
>> >> Techtoolslist mailing list
>> >> Techtoolslist@flippers.com
>> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> >> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>> >>
>> >_______________________________________________
>> >Techtoolslist mailing list
>> >Techtoolslist@flippers.com
>> >http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> >FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> >Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>> _______________________________________________
>> Techtoolslist mailing list
>> Techtoolslist@flippers.com
>> http://seven.pairlist.net/mailman/listinfo/techtoolslist
>> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>>
>_______________________________________________
>Techtoolslist mailing list
>Techtoolslist@flippers.com
>http://seven.pairlist.net/mailman/listinfo/techtoolslist
>FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
>Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
_______________________________________________
Techtoolslist mailing list
Techtoolslist@flippers.com
http://seven.pairlist.net/mailman/listinfo/techtoolslist
FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
Received on Sat Apr 13 01:07:47 2013