Re: Fluke 9010A Install with FIDE

I didn't think the Fluke 9010 did flow control. But now that I look at the
back of the unit the 25 pin connector has:

2 TD
3 RD
4 RTS
7 GND
20 DTR

So it might do some (no pin's 5 or 6 so no CTS, or DSR).

-----Original Message-----
From: techtoolslist-bounces@flippers.com
[mailto:techtoolslist-bounces@flippers.com] On Behalf Of Rodger Boots
Sent: Friday, April 12, 2013 10:28 PM
To: Technical Tools Mail List
Subject: Re: [Techtoolslist] Fluke 9010A Install with FIDE

There are multiple ways to do null modem, but it looks like the one most
likely to work would be wired like this:

DB9 DB25

  1 -

  2 2

  3 3

  4 6

  5 7

  6 20

  7 5

  8 4

  9 -

On Sat, Apr 13, 2013 at 12:07 AM, JJ <rugd2go@comcast.net> wrote:

> I think the cable is the issue. I'm running a db9 on the PC end and a
> db25 on the fluke end. I believe I need pin 7 of the db9 to pin 5 of
> the
> db25 as well as pin 8 of the db9 to pin 4 of the db25. These are the
> request and clear to send and none of these ohm out. I believe these are
> the handshake. I will try the low baud as suggested.
>
> Thanks
>
>
> Justin
>
> Sent from my Verizon Wireless 4G LTE DROID
>
> Rodger Boots <rlboots2@gmail.com> wrote:
>
> >Another possible way to help your problem is to decrease the baud rate.
> >What typically happens at high baud rates is that data transfers fine
> until
> >you hit a carriage return, then all the data that was just sent has
> >to be processed. If the sender keeps going you overrun the character
> >buffer in the receiving device. Something as old as a 29A wouldn't
> >handle more than
> >2 characters before overflowing. That's where handshaking comes in.
> >But if you use hardware handshaking (the best choice at high speeds),
> >the device stops the computer from sending until it's ready to go again.
> >
> >But you can run without any handshaking if the baud rate is low enough.
> >
> >So if you set the baud rate to something nasty slow (like 1200 or
> >less)
> and
> >the two machines then worked THAT would tell you that handshaking is
> >the problem. At least gives a clue.
> >
> >
> >On Fri, Apr 12, 2013 at 9:38 PM, JJ <rugd2go@comcast.net> wrote:
> >
> >> I tried the prior and all my settings look good. Anyone have the
> >> cable pin outs? I would like to ohm out the cable.
> >>
> >> Thanks
> >>
> >> Justin
> >>
> >> Sent from my Verizon Wireless 4G LTE DROID
> >>
> >> Rodger Boots <rlboots2@gmail.com> wrote:
> >>
> >> >Flow control is probably off or set wrong on computer end. Open
> >> >up
> >> control
> >> >panel, system, hardware, com ports. Selects your com port and
> >> >port settings. Flow control should be XON/XOFF for software flow
> >> >control or Hardware for hardware flow control. Use whichever
> >> >matches the
> programmer
> >> >setup.
> >> >
> >> >If you're using Hardware and it doesn't work your null modem cable
> >> >may
> be
> >> >wired wrong.
> >> >
> >> >Good luck.
> >> >
> >> >
> >> >On Fri, Apr 12, 2013 at 5:36 PM, JJ <rugd2go@comcast.net> wrote:
> >> >
> >> >> I tried to connect to my 9010a and laptop using xp and received
> >> >> a
> buffer
> >> >> overrun or overflow message on the 9010. Any ideas on what the
> >> >> cause
> >> might
> >> >> be? I was using a null cable.
> >> >>
> >> >> Justin
> >> >>
> >> >> Sent from my Verizon Wireless 4G LTE DROID
> >> >>
> >> >> Matthew Rossiter <matt@rossiters.com> wrote:
> >> >>
> >> >> >Has anyone gotten Fluke FIDE to work in Windows 7? I've always
> just
> >> >> >used my old Win XP laptop with a USB/Serial adapter and it
> >> >> >works
> great.
> >> >> >
> >> >> >On 4/12/2013 11:13 AM, Theron Troxel wrote:
> >> >> >>
> >> >> >> I found out what I was doing wrong. Didn't have a null modem
> cable
> >> >> adapter. Ended up ordering a serial cable adapter, which I knew
> >> >> I
> >> didn't
> >> >> want. Will try again with the correct part.
> >> >> >>
> >> >> >> ________________________________
> >> >> >> From: Theron Troxel <troxelone@yahoo.com>
> >> >> >> To: Technical Tools Mail List <techtoolslist@flippers.com>
> >> >> >> Sent: Friday, April 12, 2013 1:07 PM
> >> >> >> Subject: Re: [Techtoolslist] Fluke 9010A Install with FIDE
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> >>
> >> >> >> ________________________________
> >> >> >> From: Theron Troxel <troxelone@yahoo.com>
> >> >> >> To: "techtoolslist@flippers.com" <techtoolslist@flippers.com>
> >> >> >> Sent: Monday, April 1, 2013 5:50 PM
> >> >> >> Subject: [Techtoolslist] Fluke 9010A Install with FIDE
> >> >> >>
> >> >> >> Trying to get my fluke to respond to my computer. I have a
> >> USB-to-RS232
> >> >> cord, and my computer recognize the cord. I went to settings on
> >> >> my
> >> computer
> >> >> and set it to com1 and matched everything to the computer and fluke.
> >> >> >>
> >> >> >> Wrote a simple program that just displays "test" and tried
> sending it
> >> >> through the Fluke FIDE software. The fluke never responds to
> >> >> when I
> send
> >> >> the program. I don't get any errors of any type on the fluke.
> However,
> >> on
> >> >> the Fluke FIDE I get the following error:
> >> >> >>
> >> >> >>
> >> >> >> Starting process...
> >> >> >> WARNING: Include file already exists. File may have been
> >> >> >> included multiple times, or two files with the exact same
> >> >> >> file name may
> exist.
> >> >> >> It is recommended that you give your files distictive file names.
> >> >> >> C:\Program Files (x86)\Fluke FIDE\Scripts\test.9lc ->
> >> >> >> C:\Program
> >> Files
> >> >> (x86)\Fluke FIDE\Internal\test.9lc (exists).
> >> >> >> ERROR: Could not create batch file C:\Program Files
> >> >> >> (x86)\Fluke
> >> >> FIDE\Internal\9lc.bat.
> >> >> >> Permission denied
> >> >> >> Batch
> >> >> >> file processing failed.
> >> >> >> _______________________________________________
> >> >> >> Techtoolslist mailing list
> >> >> >> Techtoolslist@flippers.com
> >> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> >> >> Archive site:
> >> >> >> http://seven.pairlist.net/pipermail/techtoolslist/
> >> >> >> _______________________________________________
> >> >> >> Techtoolslist mailing list
> >> >> >> Techtoolslist@flippers.com
> >> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> >> >> Archive site:
> >> >> >> http://seven.pairlist.net/pipermail/techtoolslist/
> >> >> >> _______________________________________________
> >> >> >> Techtoolslist mailing list
> >> >> >> Techtoolslist@flippers.com
> >> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> >> >> Archive site:
> >> >> >> http://seven.pairlist.net/pipermail/techtoolslist/
> >> >> >
> >> >> >_______________________________________________
> >> >> >Techtoolslist mailing list
> >> >> >Techtoolslist@flippers.com
> >> >> >http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> >> >FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> >> >Archive site:
> >> >> >http://seven.pairlist.net/pipermail/techtoolslist/
> >> >> _______________________________________________
> >> >> Techtoolslist mailing list
> >> >> Techtoolslist@flippers.com
> >> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> >> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
> >> >>
> >> >_______________________________________________
> >> >Techtoolslist mailing list
> >> >Techtoolslist@flippers.com
> >> >http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> >FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> >Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
> >> _______________________________________________
> >> Techtoolslist mailing list
> >> Techtoolslist@flippers.com
> >> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
> >>
> >_______________________________________________
> >Techtoolslist mailing list
> >Techtoolslist@flippers.com
> >http://seven.pairlist.net/mailman/listinfo/techtoolslist
> >FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> >Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
> _______________________________________________
> Techtoolslist mailing list
> Techtoolslist@flippers.com
> http://seven.pairlist.net/mailman/listinfo/techtoolslist
> FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
> Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
>
_______________________________________________
Techtoolslist mailing list
Techtoolslist@flippers.com
http://seven.pairlist.net/mailman/listinfo/techtoolslist
FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
Archive site: http://seven.pairlist.net/pipermail/techtoolslist/

_______________________________________________
Techtoolslist mailing list
Techtoolslist@flippers.com
http://seven.pairlist.net/mailman/listinfo/techtoolslist
FTP site is: ftp://ttl.arcadetech.org/TTL/Test_Equipment
Archive site: http://seven.pairlist.net/pipermail/techtoolslist/
Received on Sat Apr 13 17:23:14 2013