Re: Replacement 19' Amplifone tube? tube Base Cap??

If he doesn't want the tube, I would be very interested! I am willing to give
you something for going out of your way to get it, also.

Also, do you have any other amplifone items (or WG) that you would want to
sell?

Thanks,
Joe..

nej@airmail.net wrote:

> Michael,
>
> It was my pleasure to respond! Your article is what
> got me working on amplifones in the first place! :-)
>
> I am by far no expert on the various tube scenarios,
> but I have made one of the "hybrid" monitors using an
> amplifone tube/yoke along with WG6100 boards. I have
> also followed closely all the vectorlist posts on this
> issue. I believe the common consensus is this: If
> you are using a 19VLUP22 tube, it's best to use the
> yoke out of a WG6100. Since both are 100 degree
> deflection angle (non-standard for 19" tubes). Using
> the yoke from an amplifone (a 90 degree yoke which is
> pretty standard for 19") with the 19VLUP22 tube will
> most likely make it extremely difficult to converge
> the picture. But you're welcome to give it a try! ;-)
> If this is the approach you want to take, I'll be
> happy to send you a base cap to put on the 19VLUP22
> tube. Just send me your address.
>
> Oh, and if you can't get convergence right using the
> amplifone yoke on the 19VLUP22, LMK and I might be
> willing to trade you a WG6100 yoke for yours. I'll
> have to take inventory of what yokes I have in the
> garage.
>
> What you might have been able to do was actually order
> the proper amplifone tube replacement. The original
> tube was usually Rauland M48AAWOOX (medium res), but
> there were a few others. I believe someone posted the
> cross that Richardson was selling was 19VATP22.
> Problem was they wanted $185 for these, I believe.
> Another much less expensive approach is to use a used
> low res tube out of a raster monitor. Most rasters of
> that era had the same pinout, base cap, and deflection
> angle (90 degrees) as the amplifone. So the tubes
> should mate up well with the amplifone yoke (also 90
> degrees). The 19VLUP22 you have ordered is low res
> anyway, so you aren't getting the benefits of the
> original medium res amplifone tube with your approach.
> What you could do is pull the tube out of a dead
> Electrohome G07 or WG4900 and put your amplifone yoke
> on it. I have seen this work quite nicely.
>
> Lastly, I do know a place in Dallas that was selling a
> rebuilt 19VATP22 (the original amplifone tube
> replacement) for around $125. But I haven't been over
> there in a year, nor have I actually tried using one
> of their tubes before. I would have to buy it and
> have it shipped to you, as I don't think they do
> shipping. But I could check. I suppose I could also
> test the tube in my Star Wars with a spare yoke I have
> if you wish.
>
> Oh, and with respect to your question about tube rebuilding,
> only the guns are replaced during a rebuild. They won't (or can't)
> replace the phosphur coating. But thankfully they won't rebuild a tube
> with burn in, so it should appear new.
>
> Good luck!
> Noel
>
> >
> > Thanks to Noel for his kind response. I should have stated things more
> > clearly - I am replacing the entire WG 6100 monitor in my Gravitar
> > cabinet with an Amplifone. I have all components (WinTroned HV unit,
> > Delflection board, Ampifone mounting brackets, and Amplifone yoke)
> > except for the tube.
> > I just ordered the 19VLUP22 from Richardson. I'm guessing I will
> > have to
> > replace the base cap of the 19VLUP22 in order for it to work with the
> > Amplifone, correct? Also, Richardson says these tubes are
> > "rebuilt". Is there still a chance of phospher burn on a rebuilt tube?
> > Also, any idea where I might get a base cap for the 19VLUP22 that will
> > work with the Amplifone? I don't have any extra old tubes laying
> > around here. Perhaps someone on the list has one to sell??
> >
> > Thanks Very Much,
> > Michael Kelley
> >
> ---------------------------------------------------------------------------
> > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
> > the ** message body to vectorlist-request@synthcom.com. Please direct
> > other ** questions, comments, or problems to neil@synthcom.com.
>
> ---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to neil@synthcom.com.

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Fri Nov 9 16:43:45 2001