Re: wg6100 ? HV glow but still no deflection

     I just replaced the 2N3716 at Q102. Now I have +/-25 vdc coming
from pins 4 and 5 of P100.
The spot killer LED is on now. still no picture but have HV glow. Not
sure where I should look next. Should I check the rest of the power
transistors on the chassis?

Daniel Piraino wrote:

> Im getting the proper voltage of +/- 26 vdc at pins 3 and 6 so i
> would have to say its not the LV2000. besides this is the second
> LV2000 I have tried. Its when i check pins 4 and 5 of P100,which is
> the output from the low voltage power transistors that i get a lower
> reading than normal. pin4 reads -5.68 and pin 5 reads -20. Its suppose
> to be .5 to1 volt lower than the output of the LV2000. I checked those
> power transistors before and even replaced the 2N3792 at Q103. Im
> going to go back through them again. Maybe Q102 is bad. Anyone out
> there think it might be something else?
>
> Joe Bachmann wrote:
>
>>Have you tried adjusting the voltage on the LV2000? Perhaps the pots are just a bit of.
>>
>>Or, maybe your LV2000 is bad?!??!?
>>
>>JB
>>
>>Jon Raiford wrote:
>>
>>>Since the WG6100 doesn't have a single part rectifier, I would assume you are referring to the bridge rectifier in the power supply. I think you should take a look at the rectifying diodes on the deflection board along with the filter caps behind them on the (-) side. These are not replaced in the standard cap kit, but are in the extra parts kit.
>>>
>>>Jon
>>>
>>>At 09:43 PM 2/14/2002 -0800, you wrote:
>>>
>>>> I just got the proper voltages going to the lv2000 on the deflection board. Had to put in a new big blue cap and a bridge rectifier. I get -/+26vdc at pins 3 and 6 of P100 but when I check the voltage at pin 4 and 5 with everything plugged in I get -20 vdc at pin 5 and -5 vdc at pin 4. I should be getting voltages just under -/+26vdc shouldnt I? Thats what the LV2000 directions say. I replaced the power transistor that P100 comes from, so im kind of confused on whats wrong. All the transistors checked out before, unless something just went wrong with one of them. Anyone have a suggestion?
>>>>Dan
>>>>
>>>>---------------------------------------------------------------------------
>>>>** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
>>>>** message body to vectorlist-request@synthcom.com <mailto:vectorlist-request@synthcom.com>. Please direct other
>>>>** questions, comments, or problems
>>>> to neil@synthcom.com <mailto:neil@synthcom.com>.
>>>>
>>>---------------------------------------------------------------------------
>>>** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
>>>** message body to vectorlist-request@synthcom.com <mailto:vectorlist-request@synthcom.com>. Please direct other
>>>** questions, comments, or problems to neil@synthcom.com <mailto:neil@synthcom.com>.
>>>
>>
>>---------------------------------------------------------------------------
>>** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
>>** message body to vectorlist-request@synthcom.com <mailto:vectorlist-request@synthcom.com>. Please direct other
>>** questions, comments, or problems to neil@synthcom.com <mailto:neil@synthcom.com>.
>>
>

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Sat Feb 16 10:25:52 2002