Re: New BattleZone owner.....you know whats next

Digikey, mouser, bob roberts all should have most of the parts you need if
not all (sockets, Ram, eproms, etc)

Good luck on the monitor parts ;) You'll just have to keep your eyes open
and ask around.

Fred

----- Original Message -----
From: "William Bowie" <wbowie@sc.rr.com>
To: <vectorlist@vectorlist.org>
Sent: Thursday, February 12, 2004 3:25 PM
Subject: Re: VECTOR: New BattleZone owner.....you know whats next

> So would Bob Roberts be a good source for all the parts I need? And would
> anyone know where I can get monitor boards for my 15"WG ?
> ----- Original Message -----
> From: "Fredk" <Arcadexpo@mchsi.com>
> To: <vectorlist@vectorlist.org>
> Sent: Thursday, February 12, 2004 2:44 PM
> Subject: Re: VECTOR: New BattleZone owner.....you know whats next
>
>
> > I can give you my 2 cents on this (pretty much the standard BZ treatment
> > from most of the vector guys I am sure)
> >
> > First clean up all the bad solders like you have done.
> > Then -
> >
> > 1) replace all the Rom sockets with machine sockets
> > 2) replace all the Roms with Fresh
> > 3) replace all the 40 pin sockets on the Aux PCB and replace the 2901's
> with
> > new (I do this just to save headaches later)
> >
> > This above usually takes care of most intermittent problems and make
life
> > easier to diagnois the true problem with the board.
> >
> > Fred
> >
> >
> > ----- Original Message -----
> > From: "William Bowie" <wbowie@sc.rr.com>
> > To: <vectorlist@vectorlist.org>
> > Sent: Thursday, February 12, 2004 12:56 PM
> > Subject: Re: VECTOR: New BattleZone owner.....you know whats next
> >
> >
> > > Hi Guys!
> > > I recently aquired a BattleZone mini. It has some signs of life.
> > > Currently in test mode all I get is a continuous series of low
> tones...it
> > > never stops. When I put it in game mode I will hear the attract theme
> > > followed by two explosions. When I put a credit it on the machine it
> > takes
> > > about 30sec for it to register the credit. Starting the game ..it
> sounds
> > > like its starting normal..but less than 10sec the the credit switches
> > start
> > > clicking and the game resets. I have no video yet as the monitor is
> only
> > a
> > > tube...I'm trying to find a chassis.
> > >
> > > I have been searching through the vector archives and have tried
> cleaning
> > > and re-seating all socketed chips. Cleaning and re-flowing solder on
the
> > > inter-connect. Re-flowing solder on all sockets. I am a newb to
vector
> > > games and am hoping to get some help here. I have borrowed a friends
> > > o-scope..and with direction can take readings and report results back.
> > All
> > > voltages have checked out except the +15v. How do I test the Big Blue
> cap
> > > on the brick to be sure if it needs replacement?
> > >
> > > Thanks!
> > > William
> > >
> >
>
> --------------------------------------------------------------------------
> > -
> > > ** Unsubscribe, subscribe, or view the archives at
> > http://www.vectorlist.org
> > > ** Please direct other questions, comments, or problems to
> > chris@westnet.com
> > >
> >
>
> --------------------------------------------------------------------------
> -
> > ** Unsubscribe, subscribe, or view the archives at
> http://www.vectorlist.org
> > ** Please direct other questions, comments, or problems to
> chris@westnet.com
> >
>
> --------------------------------------------------------------------------
-
> ** Unsubscribe, subscribe, or view the archives at
http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to
chris@westnet.com
>

---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com
Received on Thu Feb 12 17:11:57 2004