Re: Arghhhhhhhhhh!

Actually I have a large piece of toughened glass from a Taito cocktail I
could work behind :)
----- Original Message -----
From: "Jess Askey" <jess@askey.org>
To: <vectorlist@vectorlist.org>
Sent: Monday, August 28, 2006 7:47 PM
Subject: Re: VECTOR: Arghhhhhhhhhh!

>I never said it was a good idea, but statistically, it should be pretty
>safe. :-)
>
> I have done plenty worst to CRT's and Im still alive and kicking (Im 36).
> So either Darwin was a fool or Im just lucky. Now I realize that Im
> starting to push the envelope on odds and Darwin at this point so I don't
> think I would do this again (unless I was drunk perhaps).
>
> Hopefully, that is a good enough disclaimer. :-) :-)
>
> But seriously, if Simon is young and has enough facial hair to cover any
> subsequent scars left by the flying glass (remember, he said he would wear
> goggles), then let er rip!! (or Imp if you will).
>
>
>
> Rodger Boots wrote:
>> And this doesn't sound like a bad idea to anyone??
>>
>> For your families sake (if you have one) make sure your life insurance is
>> paid up and doing something like this isn't classified as attempted
>> suicide.
>>
>>
>> simon wrote:
>>> Hi Jess
>>> Yes sounds like a job to wear googles for sure, I can see the end of the
>>> pin but I'm not sure if I can get it hot enough to tin. Worth a try I
>>> guess. Thanks
>>>
>>> ----- Original Message -----
>>> *From:* Jess Askey <mailto:jess@askey.org>
>>> *To:* vectorlist@vectorlist.org <mailto:vectorlist@vectorlist.org>
>>> *Sent:* Monday, August 28, 2006 1:58 AM
>>> *Subject:* Re: VECTOR: Arghhhhhhhhhh!
>>>
>>> I did this exact same thing on a G-07 Raster monitor about 20 years
>>> ago. The method I used is still going strong on mine....
>>>
>>> If you can still actually get to the tip of the broken pin the
>>> glass, I used a fine tipped soldering iron to tin the end of the pin
>>> in the glass. Then, I tinned the end of the broken pin. Holding the
>>> pin with a pair of needlenose pliers, I held the pin in position
>>> while applying heat with the iron on the pin. Once I felt the solder
>>> melt and the pin slightly push inwards with the slight pressure from
>>> the pliers, I held steady and took off the heat. This worked very
>>> well for me and I then put some epoxy around the base of the pin to
>>> support it better.
>>>
>>> Now, there are some inherent dangers in this I suppose (I was only
>>> 17 when I did this). My pin was a bit below the glass, so I just
>>> sort of ground down the glass edges with my soldering iron tip in a
>>> drilling fashion until my tip hit the broken pin base.
>>>
>>> I was of course doing this with my head turned and eyes closed for
>>> safety purposes. ;-)
>>
>> ---------------------------------------------------------------------------
>>
>> ** Unsubscribe, subscribe, or view the archives at
>> http://www.vectorlist.org
>> ** Please direct other questions, comments, or problems to
>> chris@westnet.com
>
> ---------------------------------------------------------------------------
> ** Unsubscribe, subscribe, or view the archives at
> http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to
> chris@westnet.com
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.405 / Virus Database: 268.11.6/428 - Release Date: 8/25/2006
>
>

---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com
Received on Mon Aug 28 16:11:46 2006