Re: WG6100 issue

I had one that had the non-inductive look to some extent that was solved by removing the green box capacitors.. Not sure if it was one or both though.

--- On Tue, 4/14/09, Andre Huijts <a.huijts@upcmail.nl> wrote:

> From: Andre Huijts <a.huijts@upcmail.nl>
> Subject: Re: VECTOR: WG6100 issue
> To: vectorlist@vectorlist.org
> Received: Tuesday, April 14, 2009, 1:47 AM
> Thanks, the text on the
> resistors says: RGN10 1.5 OhmsJ and next line NOBLE 17. It
> looks as if those are the original one's. Can't find
> anything on google with this info....maybe some 6100 can
> verify these are original or not ?  
> Here's a picture of the deflection board
> before I started working on it (and cleaned
> it):web.jpg
>
> Thanks, André
>
> Op 13 apr 2009, om 23:23 heeft Scott Swazey het
> volgende geschreven:
> IIRC, Some of the parts were stamped
> "NI".  Just read the part number off the
> resistor and look it up on Google.
>
> -Scott
>
>
> At 02:11 PM 4/13/2009, Andre Huijts wrote:
> That is a brilliant hint, thanks !
>
> Stupid from me as
> I've read about this before but thought it was
> Amplifone only....
>
> Gonna check it out.
> Anyway I can recognize if they're non-inductive or
> not ?
>
> Thanks !
>
> Op 13 apr 2009, om
> 22:43 heeft Scott Swazey het volgende geschreven:
>
> > Check the two big
> 10W resistors.  It should be a non-inductive part.
> >
> > -Scott
> >
> > At 10:58 AM
> 4/13/2009, you wrote:
> >> I'm
> working on this WG6100 where some vectors (esp. on the
> letters)
> >> seem to be
> badly drawn.
> >>
> >> Check out
> this very short video:
> >>
> >> http://www.youtube.com/watch?v=_pmbmheq7Gg
> >>
> >> Note the W
> and the other letters don't look as nice as on my
> >> Amplifone.
> >>
> >> The PCB set
> is normally running in my cockpit and working fine on my
> >> 25"
> Amplifone so it's not a PCB issue.
> >> The WG6100
> has a LV2000 installed, cap-kit and redone all solderings
> >> on deflection
> and neck pcb.
> >> LV2000
> voltages are exactly set at 26.00V and -26.00V
> >> As mentioned
> PCB set works fine, BIP is correctly set-up.
> >>
> >> Is this
> because of WG's lower slew-rate or can something be done
> to
> >> correct this
> ?
> >>
> >> Thanks.
> >>
> ---------------------------------------------------------------------------
> >> **
> Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
> >> ** Please
> direct other questions, comments, or problems to chris@westnet.com
> >
> >
> ---------------------------------------------------------------------------
> > ** Unsubscribe,
> subscribe, or view the archives at http://www.vectorlist.org
> > ** Please direct
> other questions, comments, or problems to chris@westnet.com
>
> André Huijts
> andre.huijts@upcmail.nl
>
>
>
>
>
> ---------------------------------------------------------------------------
> ** Unsubscribe,
> subscribe, or view the archives at http://www.vectorlist.org
> ** Please direct other
> questions, comments, or problems to chris@westnet.com
>
> ---------------------------------------------------------------------------
> ** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to
> chris@westnet.com
>
> André
> Huijtsandre.huijts@upcmail.nl
>
>
>
>
> __________________________________________________________________ Be smarter than spam. See how smart SpamGuard is at giving junk email the boot with the All-new Yahoo! Mail. Click on Options in Mail and switch to New Mail today or register for free at http://mail.yahoo.ca
---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com
Received on Thu Apr 16 14:39:57 2009