Sometimes the PCI IRQs are set from one of the BIOS setup screens.
On Sep 12, 2011 10:33 PM, "Michael Cunningham" <
michael.cunningham.usa@gmail.com> wrote:
> easier said then done:) I have disabled the serial port in the bios
> so that shouldnt be
> an issue. Basically when I move it from pci slot to slot the irq changes.
>
> I've seen irq 4, 10, and 11
>
>
>
> On Mon, Sep 12, 2011 at 11:18 PM, Rodger Boots <rlboots2@gmail.com> wrote:
>> You might want to move the sound card to IRQ5, IRQ4 is usually one of the
>> serial ports.
>>
>> On Sep 12, 2011 10:13 PM, "Michael Cunningham"
>> <michael.cunningham.usa@gmail.com> wrote:
>>> Some success...
>>>
>>> I popped out 3 of the 1gb chips.. down to 1gb now.
>>>
>>> Was able to sucessfully load dos 7.1 and got the sbpci drivers
installed.
>>> dvmame now runs but I get a page fault error when I try to
>>> start it up with sound. Choosing silence works great.
>>>
>>> I'm assuming my sb setup is screwed up but it loads the driver fine
>>> when dos boots
>>> and reports port ccc0 irq 4
>>>
>>> I tried the sbtest program and it just hangs when it hits the digital
>>> voice test. I'm
>>> thinking this is one of those nightmare to config sb pci cards.
>>>
>>> What SB pci cards is everyone using? model num?
>>>
>>> I have a CT4750
>>>
>>>
>>>
>>> On Mon, Sep 12, 2011 at 3:14 PM, matt <galaga@slingshot.co.nz> wrote:
>>>> 64mb is all you need for vdmame !!
>>>> ----- Original Message ----- From: "Michael Cunningham"
>>>> <michael.cunningham.usa@gmail.com>
>>>> To: <vectorlist@vectorlist.org>
>>>> Sent: Tuesday, September 13, 2011 3:21 AM
>>>> Subject: Re: VECTOR: ZVG Experience - Proper place to post?
>>>>
>>>>
>>>> Thats a good point. I think my bois has an option to limit the ram to
>>>> 256 mb for older operating systems. I'll give that a try when I get
>>>> home. I assume 256 mb be enough to cover all the vector
>>>> games.
>>>>
>>>>
>>>> On Mon, Sep 12, 2011 at 10:38 AM, Lewis D'Aubin <ldaubin@bellsouth.net>
>>>> wrote:
>>>>>
>>>>>> What version of DOS are you using?
>>>>>> Any links for the drivers and such you used?
>>>>>>
>>>>>> I've been pulling my hair out with dos. I think there is something
>>>>>> wrong with my motherboard as all the memory (4 gb!) seem to be used
up
>>>>>> in dos so nothing can start.
>>>>>
>>>>> 4GB? Try pulling out three of those... there's no way DOS can address
>>>>> that
>>>>> much memory. My VectorMAME cab is running sweet on 64MB.
>>>>>
>>>>> -Lewis
>>>>>
>>>>>
>>>>>
>>>>>
---------------------------------------------------------------------------
>>>>> ** Unsubscribe, subscribe, or view the archives at
>>>>> http://www.vectorlist.org
>>>>> ** Please direct other questions, comments, or problems to
>>>>> chris@westnet.com
>>>>>
>>>>
>>>>
---------------------------------------------------------------------------
>>>> ** Unsubscribe, subscribe, or view the archives at
>>>> http://www.vectorlist.org
>>>> ** Please direct other questions, comments, or problems to
>>>> chris@westnet.com
>>>>
>>>> __________ Information from ESET NOD32 Antivirus, version of virus
>>>> signature
>>>> database 6238 (20110625) __________
>>>>
>>>> The message was checked by ESET NOD32 Antivirus.
>>>>
>>>> http://www.eset.com
>>>>
>>>>
>>>>
>>>>
>>>>
---------------------------------------------------------------------------
>>>> ** Unsubscribe, subscribe, or view the archives at
>>>> http://www.vectorlist.org
>>>> ** Please direct other questions, comments, or problems to
>>>> chris@westnet.com
>>>>
>>>
>>>
---------------------------------------------------------------------------
>>> ** Unsubscribe, subscribe, or view the archives at
>>> http://www.vectorlist.org
>>> ** Please direct other questions, comments, or problems to
>>> chris@westnet.com
>>
>
---------------------------------------------------------------------------
> ** Unsubscribe, subscribe, or view the archives at
http://www.vectorlist.org
> ** Please direct other questions, comments, or problems to
chris@westnet.com
---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com
Received on Mon Sep 12 23:35:46 2011
This archive was generated by hypermail 2.1.8 : Mon Sep 12 2011 - 23:50:02 EDT