Ok. So the black and orange go to the center pin of 15 brick. On the female
side they turn into two white and orange leads. Each one goes to a three
pin plug where only two pins are used and the wires are bridged with what
looks like a diode. One plug goes to the coin counter the other one is empty
On Oct 10, 2013 7:53 PM, "Rodger Boots" <rlboots2@gmail.com> wrote:
> That would be J40. It plugs into P40 (on a loose connector that goes to
> power supply in bottom of cabinet).
>
>
> On Thu, Oct 10, 2013 at 9:47 PM, Joel Griffin Dodd <griffindodd@gmail.com>wrote:
>
>> I have nothing on e and 18 dead as a dead dodo that died. That orange and
>> black wire looks like it goes to a 9 pin connector block with no home.
>> On Oct 10, 2013 7:42 PM, "Rodger Boots" <rlboots2@gmail.com> wrote:
>>
>>> Comes to game board on connector pins E & 18.
>>>
>>> I have GOT to find a better scan of the schematics, what I have is
>>> nearly unreadable.
>>>
>>>
>>> On Thu, Oct 10, 2013 at 9:34 PM, Joel Griffin Dodd <
>>> griffindodd@gmail.com> wrote:
>>>
>>>> So.... I have no 10.3vun at the test tab on the game board. Does that
>>>> come from the ar2 via the edge connector or is it stepped down from one of
>>>> the higher voltage feeds on the board?
>>>> On Oct 10, 2013 6:17 AM, "Joel Griffin Dodd" <griffindodd@gmail.com>
>>>> wrote:
>>>>
>>>>> The trouble shooting guide says you can remove the soundboard to do
>>>>> these tests
>>>>> On Oct 10, 2013 4:25 AM, "Douglas Gauck" <douglas@gauck.com> wrote:
>>>>>
>>>>>> Really? I had my main board on the bench all by itself. What it did
>>>>>> need was the 10.3 (in fact I hooked up all voltages -5, +5, +10.3 and +12)
>>>>>>
>>>>>> On Oct 10, 2013, at 12:32 AM, Rodger Boots <rlboots2@gmail.com>
>>>>>> wrote:
>>>>>>
>>>>>> Reset not going to work without sound board.
>>>>>>
>>>>>>
>>>>>> On Wed, Oct 9, 2013 at 11:29 PM, Joel Griffin Dodd <
>>>>>> griffindodd@gmail.com> wrote:
>>>>>>
>>>>>>> Interconnects are good. No I didn't have the sound board installed
>>>>>>> during these tests.
>>>>>>> On Oct 9, 2013 9:25 PM, "Rodger Boots" <rlboots2@gmail.com> wrote:
>>>>>>>
>>>>>>>> Reset comes indirectly through sound board. Do you have a sound
>>>>>>>> board installed and are interconnect cables in good shape?
>>>>>>>> On Oct 9, 2013 11:07 PM, "Joel Griffin Dodd" <griffindodd@gmail.com>
>>>>>>>> wrote:
>>>>>>>>
>>>>>>>>> All my clocks test good on my oscilloscope the only one I haven't
>>>>>>>>> found a test point for is 1.5mhz where is that point.? Got a solid 1.5mhz
>>>>>>>>> at E and Q though at the cpu
>>>>>>>>> On Oct 9, 2013 9:05 PM, "Rodger Boots" <rlboots2@gmail.com> wrote:
>>>>>>>>>
>>>>>>>>>> Start looking for where these come from and work your way back.
>>>>>>>>>> You did check for missing/broken crystal, right?
>>>>>>>>>> On Oct 9, 2013 11:00 PM, "Joel Griffin Dodd" <
>>>>>>>>>> griffindodd@gmail.com> wrote:
>>>>>>>>>>
>>>>>>>>>>> Yep both still low with CPU removed
>>>>>>>>>>> On Oct 9, 2013 8:55 PM, "Rodger Boots" <rlboots2@gmail.com>
>>>>>>>>>>> wrote:
>>>>>>>>>>>
>>>>>>>>>>>> Could be, remove the CPU and see if they are still low. That
>>>>>>>>>>>> will tell you if it is the CPU or the board.
>>>>>>>>>>>> On Oct 9, 2013 10:50 PM, "Joel Griffin Dodd" <
>>>>>>>>>>>> griffindodd@gmail.com> wrote:
>>>>>>>>>>>>
>>>>>>>>>>>>> Hey guys. Troubleshooting my non booting star wars board set.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Checked all my voltages and clicks they look good.
>>>>>>>>>>>>> Firq, NMI and halt are all high
>>>>>>>>>>>>> However reset is permanently low as is Irq at the CPU.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Any ideas where to go from here? Bad CPU?
>>>>>>>>>>>>>
>>>>>>>>>>>>> I'm following the star wars troubleshooting guide
>>>>>>>>>>>>>
>>>>>>>>>>>>> Joel
>>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>
>>>>>>
>>>
>
---------------------------------------------------------------------------
** Unsubscribe, subscribe, or view the archives at http://www.vectorlist.org
** Please direct other questions, comments, or problems to chris@westnet.com
Received on Thu Oct 10 22:57:03 2013
This archive was generated by hypermail 2.1.8 : Thu Oct 10 2013 - 23:50:01 EDT