RE: Wintron install: Does this look right?

Hmmm....

For the grey wire I followed the instructions in the FAQ
that had me wiring it to the "WHT" connection which is
where the grey wire from the old transformer was connected.
 You can actually see it in the pictiure marked "Component
1", the wire is coming out from between the HV and the
focus.

--- David.Fish@axcelis.com wrote:
> Hey Dan,
>
> From what I can see from your photos it looks correct.
> I can't see where you hooked up the GREY (filament) wire
> tho'. It's been quite a while since I wrote the corrected
> instructions so I refreshed my memory and included them
> below for archive purposes. If you look at your 1st
> picture
> the clockwise-most pad, where the RED wire is connected,
> is
> pad #9. The pad numbers DECREASE as you go
> COUNTER-CLOCKWISE
> since the photo is of the bottom of the board (etch
> side).
> Note that there are no pads for positions 5 and 3 but you
> still count them.
>
> [From J. A's site:]
> RED wire from XFMR to PCB hole T2 pin 9. Low side of MC1.
> YEL wire from XFMR to PCB hole T2 pin 8. This is +24VDC.
> BLK to PCB hole T2 pin 6 or 7. This is GROUND.
> GRN wire from XFMR to PCB hole T2 pin 4. Video B+,
> connects to anode of CR3.
> ORG wire from XFMR to PCB hole T2 pin 1. Goes to
> COLLECTOR of Q3 (BU406D).
> GRY wire from XFMR to PCB hole T2 pin 10. This is the
> filament's hot side.
>
> Dave
>
> > -----Original Message-----
> > From: Dan Rasmussen [mailto:sscanf@yahoo.com]
> > Sent: Tuesday, October 23, 2001 9:07 AM
> > To: vectorlist@synthcom.com
> > Subject: VECTOR: Wintron install: Does this look right?
> >
> >
> > Hi,
> >
> > Last night I finally got around to working on my Start
> Wars
> > after having a Wintron HV unit sitting on my bench for
> 2+
> > years. I downloaded the Amplifone FAQ and the
> corrected
> > Wintron install instructions (thanks to those who put
> in
> > the effort). My only problem is that the section of
> the
> > Amplifone FAQ where it describes how to install the
> Wintron
> > HV has an error.
> >
> > It explains that there are connectors (as you look at
> the
> > solder side of the board) at 7:00, 8:00, 11:00, 1:00,
> 2:00,
> > 4:00, and 5:00 ... but then it tells you to connect the
> > green wire at 9:00. I was looking at the FAQ posted
> at :
> >
> >
>
http://www.gamearchive.com/video/manufacturer/atari/vector/mon
> > itors/Amplifone/amp_hv_faq.html
> >
> > After reading through it a few times and looking at the
> > "corrected" Wintron instructions, I hooked green up at
> > 11:00. I was also not sure how to orient the new HV
> uint
> > as it takes up quite a bit of RE on the board.
> >
> > Please take a look at some pics I took and let me know
> if I
> > got this thing right (warning, long URL that might get
> > split by your mailer):
> >
> >
>
http://photos.yahoo.com/bc/drasmuss/lst?&.dir=/amplifone&.src=
> >
>
ph&.view=t&.begin=1&.order=&.done=http%3a//photos.yahoo.com/bc
> > /drasmuss/lst%3f%26.dir=/amplifone%26.src=ph%26.view=t
> >
> > Thanks very much.
> >
> > Dan Rasmussen
> >
> > PS Joel, those new thumb buttons are going in this week
> > too.
> >
> >
> > =====
> > ------ replies to sscanf@yahoo.com ------
> >
> > Anything that appears after this sentence is inserted
> by
> > Yahoo (or others) and may not be a good idea.
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Make a great connection at Yahoo! Personals.
> > http://personals.yahoo.com
> >
>
--------------------------------------------------------------
> > -------------
> > ** To UNSUBSCRIBE from vectorlist, send a message with
> > "UNSUBSCRIBE" in the
> > ** message body to vectorlist-request@synthcom.com.
> Please
> > direct other
> > ** questions, comments, or problems to
> neil@synthcom.com.
> >
>
---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE" in the
> ** message body to vectorlist-request@synthcom.com.
> Please direct other
> ** questions, comments, or problems to neil@synthcom.com.

=====
------ replies to sscanf@yahoo.com ------

Anything that appears after this sentence is inserted by
Yahoo (or others) and may not be a good idea.

__________________________________________________
Do You Yahoo!?
Make a great connection at Yahoo! Personals.
http://personals.yahoo.com
---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Tue Oct 23 07:44:38 2001