RE: Re[4]: VECTOR:Update on my latest Endeavors to Fix my STAR WA RS MAINBoard.

Matt,
*****

 Yes I already sawpped out the RAMS but
but unfortunately to no avail.

 Arcadius.......... :-)

-----Original Message-----
From: matt [mailto:galaga@clear.net.nz]
Sent: Wednesday, October 09, 2002 12:58 AM
To: vectorlist@synthcom.com
Subject: RE: Re[4]: VECTOR:Update on my latest Endeavors to Fix my STAR
WA RS MAINBoard.

have u replace all the ram chips my starwars and tempest did this!!! just
reset!!
u need the IRQ cause in the lines of code are the w/dog reset!

i hope this helps

---- Original message from: Stempak Arcadius-ASTEMPA1 ----
> Peter,
> ******
>
>
> Well I wish I had better news, but things are still the same
> IRQ Line is Constant LOW, Watchdog is still Barking.
> (Update Follows)
>
>
> I replaced the Part in Location 8M (LS138) and did Verify
> via Ohm Meter that as you stated, PINS 10 and 12 coming
> out of Part 2M (LS74) are indeed, as you stated, Connected
> to, at least on my Star Wars MAIN Board to Not a Resistor
> Pack but rather to a single Resistor R96 which is a
> 1K Ohm Resistor 1/4 Watt, and again confirmed this
> after review of the Star Wars Operators Manual Parts
> Manifest, which matched this Part, exactly.
>
> Furthermore I reviewed All of the Parts / Descriptions of such
> on this MAIN Board and again was not able to find any mention
> or physical description of any type of Resistor Pack, on either
> the MAIN, AVG or SOUND BOARD.
>
> Perhaps you meant some other part or perhaps there was a
> change in Various Board REV's. as I have the REV. C Boardset.
>
> In any case and if there is anything else you would like myself
> to confirm or replace please let me know.
>
> One question I do have and this is to anyone whom has or has had
> a Star Wars Boardset. My Manual states that All EPROMS 0-4 on
> the MAIN Board should be a 2764 Type, however on my MAIN Board
> the First EPROM which is a 27128 Type the rest are All 2764 Types.
>
> Is my Configuration Correct or does the Operators Manual which I have
> contain a Typo, in Both the Parts Description and / or Manifest, with
regard
> to the above EPROM Types ???
>
>
>
> Arcadius..................
>
> -----Original Message-----
> From: peter jones [mailto:highwayman2000@mail.ru]
> Sent: Tuesday, October 08, 2002 12:51 AM
> To: vectorlist@synthcom.com
> Subject: Re[4]: VECTOR:Update on my latest Endeavors to Fix my STAR WARS
> MAINBoard.
>
>
>
> -----Original Message-----
> From: Stempak Arcadius-ASTEMPA1 <ASTEMPA1@motorola.com>
> To: "'vectorlist@synthcom.com'" <vectorlist@synthcom.com>
> Date: Mon, 7 Oct 2002 23:30:21 -0500
> Subject: RE: Re[2]: VECTOR:Update on my latest Endeavors to Fix my STAR
WARS
> MAINBoard.
>
> >
> >
> > Peter,
> > ******
> >
> > Will proceed, as you suggested and check out Resistor Pack PR-96
> > I would like to ask you though, what the Value(s) of this Resistor Pack
> > should be ??? so I know what to expect.
> >
> it's just a pull-up resitor, so 1k/4k7/10k type of thing.
> what you are looking for is broken pins or the pack cracked!
>
> part number on sil-packs is easy, 3 digits.
> 1st 2 digits are numbers, 3rd digit is number of zero's to put at the end.
>
> ie:
> 103 = 10k (10 +3 0's)
> 472 = 4k7 (47 +2 0's)
>
> o.k. ?
>
>
>
---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
Received on Wed Oct 9 14:19:16 2002