Re: WTB: Star Wars 14-tooth spur gear

I can get original Atari 14 tooth gears but they will be $20US each as
well. Is anyone interested? About ten are left.

John :-#)#

At 06:53 PM 27/11/2002 -0600, SteveT wrote:

>The Berg gear will set you back about $20 including shipping.
>BTW you need to set up an account with them first.
>
>Steve
>
>Steven Winslow wrote:
>
> > David !
> >
> > I can confirm that the Berg part # P24A66-14 is a perfect replacement
> > (better than perfect actually).
> >
> > Steve
> >
> > At 09:44 AM 11/27/2002 -0600, you wrote:
> > >Here's my post from earlier this year, and Rodger's reply.
> > >
> > >tom mcclintock wrote:
> > >
> > > > Anyone good with gears? I need to get some replacement small gears for
> > > > my Star Wars (yes, I know you are saying don't we all). There is that
> > > > fancy yoke controller rebuild kit on eBay, but for $50-$60 plus
> shipping
> > > > it seems a bit much.
> > > >
> > > > Browsing through the manual, I discover that the two different 'small
> > > > gears' are thus:
> > > >
> > > > Tilt Gear (up and down) - 14-tooth Spur Gear (Atari Part # 040249-01)
> > > > Pan Gear (left & right) - 28-tooth Spur Gear (Atari Part # 178101-003)
> > > >
> > > > McMaster-Carr doesn't have a suitable replacement but Berg certainly
> > > > does :) (www.wmberg.com) However, we now get into pressure angles,
> pitch
> > > > and pitch diameters, hub, no hub, etc. Not my forte. Here are the two
> > > > that look most promising (and likely the same ones that can be found in
> > > > the rebuild kit on eBay).
> > > >
> > > > 14 tooth, 24 Pitch, 1/4" face aluminum spur gear - Berg Part no.
> > > > P24A66-14
> > > > 28 tooth, 24 pitch, 3/16" face delrin spur gear - Berg Part no.
> F24D5-28
> > > >
> > > > Anyone able to figure out the exact replacement parts so I don't
> ruin by
> > > > yoke controller?
> > >
> > >Rodger Boots wrote:
> > >
> > > > If you get the diameters right the pitch should be correct. For the
> > > > same number of teeth a larger pitch will be a larger diameter.
> > >
> > >
> > >
> > >tm
> > >
> > >
> > >"Fish, David" wrote:
> > >
> > > > Sorry to post a WTB here but I have not received any response from my
> > > > post in RGVAC. I need a replacement 14-tooth spur gear for my SW/ESB,
> > > > the gear that controls the up/down movement. There was a mention of a
> > > > replacement gear that was discussed here a few months ago but I don't
> > > > recall it. Do we have access to recent archived V-list posts?
> Anyway, I'm
> > > > willing but trade stuff or buy outright. Please email me at the
> attbi.com
> > > > address below.
> > > >
> > > > Thanks and have a happy Thanksgiving!
> > > >
> > > > David Fish "We want...Information.
> > > > INFORMATION
> > > > Melrose, MA USA You won't get it!
> > > > dfish1@attbi.com By hook or by crook we
> will"
> > > > David.Fish@axcelis.com _The
> > > > Prisoner_
> > > >
> ---------------------------------------------------------------------------
> > > > ** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE" in the
> > > > ** message body to vectorlist-request@synthcom.com. Please direct other
> > > > ** questions, comments, or problems to vectorlist-owner@synthcom.com.
> > >
> > >-----------------------------------------------------------------------
> ----
> > >** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
> in the
> > >** message body to vectorlist-request@synthcom.com. Please direct other
> > >** questions, comments, or problems to vectorlist-owner@synthcom.com.
> >
> > ---------------------------------------------------------------------------
> > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> > ** message body to vectorlist-request@synthcom.com. Please direct other
> > ** questions, comments, or problems to vectorlist-owner@synthcom.com.
>
>---------------------------------------------------------------------------
>** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
>** message body to vectorlist-request@synthcom.com. Please direct other
>** questions, comments, or problems to vectorlist-owner@synthcom.com.

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
Received on Fri Nov 29 08:06:39 2002