RE: WTB: Star Wars 14-tooth spur gear

Old stock or newly manufactured?

I'd think that anything older than 10 years would be ready to explode
into pieces after just a little use...

> -----Original Message-----
> From: owner-vectorlist@synthcom.com
> [mailto:owner-vectorlist@synthcom.com] On Behalf Of John Robertson
> Sent: Friday, November 29, 2002 7:52 AM
> To: vectorlist@synthcom.com; vectorlist@synthcom.com
> Subject: Re: VECTOR: WTB: Star Wars 14-tooth spur gear
>
>
> I can get original Atari 14 tooth gears but they will be
> $20US each as
> well. Is anyone interested? About ten are left.
>
> John :-#)#
>
> At 06:53 PM 27/11/2002 -0600, SteveT wrote:
>
> >The Berg gear will set you back about $20 including shipping.
> >BTW you need to set up an account with them first.
> >
> >Steve
> >
> >Steven Winslow wrote:
> >
> > > David !
> > >
> > > I can confirm that the Berg part # P24A66-14 is a perfect
> replacement
> > > (better than perfect actually).
> > >
> > > Steve
> > >
> > > At 09:44 AM 11/27/2002 -0600, you wrote:
> > > >Here's my post from earlier this year, and Rodger's reply.
> > > >
> > > >tom mcclintock wrote:
> > > >
> > > > > Anyone good with gears? I need to get some
> replacement small gears for
> > > > > my Star Wars (yes, I know you are saying don't we
> all). There is that
> > > > > fancy yoke controller rebuild kit on eBay, but for
> $50-$60 plus
> > shipping
> > > > > it seems a bit much.
> > > > >
> > > > > Browsing through the manual, I discover that the two
> different 'small
> > > > > gears' are thus:
> > > > >
> > > > > Tilt Gear (up and down) - 14-tooth Spur Gear (Atari
> Part # 040249-01)
> > > > > Pan Gear (left & right) - 28-tooth Spur Gear (Atari
> Part # 178101-003)
> > > > >
> > > > > McMaster-Carr doesn't have a suitable replacement but
> Berg certainly
> > > > > does :) (www.wmberg.com) However, we now get into
> pressure angles,
> > pitch
> > > > > and pitch diameters, hub, no hub, etc. Not my forte.
> Here are the two
> > > > > that look most promising (and likely the same ones
> that can be found in
> > > > > the rebuild kit on eBay).
> > > > >
> > > > > 14 tooth, 24 Pitch, 1/4" face aluminum spur gear -
> Berg Part no.
> > > > > P24A66-14
> > > > > 28 tooth, 24 pitch, 3/16" face delrin spur gear -
> Berg Part no.
> > F24D5-28
> > > > >
> > > > > Anyone able to figure out the exact replacement parts
> so I don't
> > ruin by
> > > > > yoke controller?
> > > >
> > > >Rodger Boots wrote:
> > > >
> > > > > If you get the diameters right the pitch should be
> correct. For the
> > > > > same number of teeth a larger pitch will be a larger diameter.
> > > >
> > > >
> > > >
> > > >tm
> > > >
> > > >
> > > >"Fish, David" wrote:
> > > >
> > > > > Sorry to post a WTB here but I have not received any
> response from my
> > > > > post in RGVAC. I need a replacement 14-tooth spur
> gear for my SW/ESB,
> > > > > the gear that controls the up/down movement. There
> was a mention of a
> > > > > replacement gear that was discussed here a few months
> ago but I don't
> > > > > recall it. Do we have access to recent archived V-list posts?
> > Anyway, I'm
> > > > > willing but trade stuff or buy outright. Please email
> me at the
> > attbi.com
> > > > > address below.
> > > > >
> > > > > Thanks and have a happy Thanksgiving!
> > > > >
> > > > > David Fish "We
> want...Information.
> > > > > INFORMATION
> > > > > Melrose, MA USA
> You won't get it!
> > > > > dfish1@attbi.com By hook
> or by crook we
> > will"
> > > > > David.Fish@axcelis.com
> _The
> > > > > Prisoner_
> > > > >
> >
> --------------------------------------------------------------
> -------------
> > > > > ** To UNSUBSCRIBE from vectorlist, send a message with
> > "UNSUBSCRIBE" in the
> > > > > ** message body to vectorlist-request@synthcom.com.
> Please direct other
> > > > > ** questions, comments, or problems to
> vectorlist-owner@synthcom.com.
> > > >
> > >
> >-------------------------------------------------------------
> ----------
> > ----
> > > >** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE"
> > in the
> > > >** message body to vectorlist-request@synthcom.com.
> Please direct other
> > > >** questions, comments, or problems to
> vectorlist-owner@synthcom.com.
> > >
> > >
> --------------------------------------------------------------
> -------------
> > > ** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE" in the
> > > ** message body to vectorlist-request@synthcom.com.
> Please direct other
> > > ** questions, comments, or problems to
> vectorlist-owner@synthcom.com.
> >
> >-------------------------------------------------------------
> --------------
> >** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE" in the
> >** message body to vectorlist-request@synthcom.com. Please
> direct other
> >** questions, comments, or problems to vectorlist-owner@synthcom.com.
>

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to vectorlist-owner@synthcom.com.
Received on Fri Nov 29 08:35:54 2002