Re: Fluke 9010A Input voltage

Re: [Techtoolslist] Fluke 9010A Input voltageJohn,

Thank you very much for this detailed information! I've succesfully modified the input voltage on my systems...

For some reason I seem to have only programming, service and pod manuals (and no operator manual) available. Do you happen to know where I could find one as download ?

I have now 3 working 9010A systems :-) but unfortunately still no 9000A-Z80 pod :-( If someone has a spare Z80 please drop me a line. I am located in Europe.

Thanks again!

Filip
  ----- Original Message -----
  From: John Robertson
  To: Technical Tools Mail List
  Sent: Monday, October 31, 2005 7:50 PM
  Subject: Re: [Techtoolslist] Fluke 9010A Input voltage

  Hi Filip,

  On all the 9010A's that I've seen (15 or so), on the rear where the international style power cord plugs in, there is a fuse under a plastic cover just below the socket. This also allows you to set the voltage with a slip in card.

  Quoting from the 9010A Operator Manual: (find yourself a copy! or download it)

  Line Voltage Selection (page 2-1)

  yada, yada, yada.

  1. Remove line fuse (slide cover up - JR)
  2. Using a pair of needlenose pliers (see Figure 2-2), pull the line voltage card straight out.
  3. Turn the card and insert it into its slot so that the value if the desired line voltage is the upper value facing the fuse slot. In Figure 2-2, the card is oriented to select 120V.

  John :-#)#

  At 8:08 PM +0100 10/31/05, Filip Hautekeete wrote:
    Steve,

    There is no panel nor switch on the back. However there is a note referring to the manual (orientation of the mains circuit board). Unfortunately I was not able to locate any information about this in the service manual. I was hoping someone had done this before and could tell me immediately what actions to perform.

    Best regards,

    Filip

      ----- Original Message -----
      From: Steve C
      To: 'Technical Tools Mail List'
      Sent: Monday, October 31, 2005 7:59 PM
      Subject: RE: [Techtoolslist] Fluke 9010A Input voltage

      Yes, there is a panel on the back that allows voltage selection - I can't remember how but it was easy.

      Steve

      -----Original Message-----
      From: techtoolslist-bounces@flippers.com [mailto:techtoolslist-bounces@flippers.com] On Behalf Of Filip Hautekeete
      Sent: 31 October 2005 13:27
      To: techtoolslist@flippers.com
      Subject: [Techtoolslist] Fluke 9010A Input voltage

      Hi all,

      Is there any easy way to switch the Fluke 9010A from VAC 120 (factory installed) to VAC 240 ?

      Best regards,

      Filip

--------------------------------------------------------------------------

      _______________________________________________
      Techtoolslist mailing list
      Techtoolslist@flippers.com
      http://seven.pairlist.net/mailman/listinfo/techtoolslist

    _______________________________________________
    Techtoolslist mailing list
    Techtoolslist@flippers.com
    http://seven.pairlist.net/mailman/listinfo/techtoolslist

------------------------------------------------------------------------------

  _______________________________________________
  Techtoolslist mailing list
  Techtoolslist@flippers.com
  http://seven.pairlist.net/mailman/listinfo/techtoolslist

_______________________________________________
Techtoolslist mailing list
Techtoolslist@flippers.com
http://seven.pairlist.net/mailman/listinfo/techtoolslist
Received on Mon Oct 31 15:50:01 2005