Re: Tech: Electrohome G05

Can you adjust the X & Y size with the size controls? It is possible that
one of them is defective. You checked the board with a good monitor in the
same cabinet as the problem is occurring in? Just to avoid any wiring
weirdness possibilities...Have you checked all the pins of any connectors
on the monitor motherboard and re-soldered them to be safe?

John :-#)#

At 04:00 AM 10/24/00, Jon Raiford wrote:
>Ok, check out Q701 and the surrounding circuit. The G05-801 manual says
>that this is the initial gain applied to the signal to correct for tube
>linearity. You can also test this in circuit by comparing voltages with
>the Y axis. Values should be almost identical.
>
>Jon
>
>At 04:40 PM 10/23/2000 +0000, you wrote:
> >i have tried a working monitor and the
> >game board is working 100%, no problems
> >there either.
> >
> >
> >>From: Jon Raiford <raiford@mindspring.com>
> >>Reply-To: vectorlist@synthcom.com
> >>To: vectorlist@synthcom.com
> >>Subject: Re: VECTOR: Tech: Electrohome G05
> >>Date: Mon, 23 Oct 2000 11:42:57 -0400
> >>
> >>Try swapping the x and y pins on the monitor connector (or try another
> known good monitor) to verify that this is a monitor problem. It sounds
> like it could be a problem with the game board.
> >>
> >>Jon
> >>
> >>At 03:18 PM 10/23/2000 +0000, you wrote:
> >> >have a later model GO5 that i would like
> >> >some help on, the monitor plays in the center
> >> >of the screen approx. 1/4" wide, the full
> >> >height of the screen, but does not go out
> >> >towards the left or right any further than
> >> >the 1/4" path, i have already installed a cap
> >> >kit with transistors and resoldered all the
> >> >head pins, with NO results, the HV unit is
> >> >working, and the spot killer DOES NOT come
> >> >on, and NO FUSES have been blown. Dont notice
> >> >anything out of the ordinary, was wondering if
> >> >someone on the list could help.
> >>
> >>---------------------------------------------------------------------------
> >>** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> >>** message body to vectorlist-request@synthcom.com. Please direct other
> >>** questions, comments, or problems to neil@synthcom.com.
> >
> >_________________________________________________________________________
> >Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
> >
> >Share information about yourself, create your own public profile at
> http://profiles.msn.com.
> >
> >---------------------------------------------------------------------------
> >** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> >** message body to vectorlist-request@synthcom.com. Please direct other
> >** questions, comments, or problems to neil@synthcom.com.
>
>---------------------------------------------------------------------------
>** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
>** message body to vectorlist-request@synthcom.com. Please direct other
>** questions, comments, or problems to neil@synthcom.com.

  John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9
  Call (604)872-5757 or Fax 872-2010 (Pinballs, Jukes, Video Games)
  http://www.flippers.com
         "Old pinballers never die, they just flip out."

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Mon Oct 23 15:31:58 2000