Re: WG 6100 GRY wire

Yes Joe, it is a ground. As a matter of fact it is the center tap to the
3-wire monitor power connection! I'm amazed anyone would cut this wire.
That gray wire goes to pin 14 on the monitor's 15-pin main input connector
(J100). It's the pin between the two violet wires on one end of the
connector. After passing through the connector, it veers off with the two
25 volt power wires. It is also the center pin on this 3-pin connector.
Once again, you would absolutely want to rework this one.

Michael

----- Original Message -----
From: "Joe Bachmann" <joe.bachmann@newmail.net>
To: <vectorlist@synthcom.com>
Sent: Wednesday, April 10, 2002 12:30 AM
Subject: Re: VECTOR: WG 6100 GRY wire

> Now I need to ask this: Is the wire marked GRY next to the large caps on
the
> deflection board also a ground?
>
> I have found on all thw WG 6100 parts I have that these wires have been
chopped
> (probably by ops.)
>
> Thanks much,
> Joe
>
> Chris Starr wrote:
>
> > I can confirm, definitely a grounding wire. Bolts on to the aluminum
chassis
> > on one of the holes between the HV chassis box and the deflection board
on
> > the right. Probably will help reduce the jitters you mentioned.
> >
> > c-starr
> >
> > ----- Original Message -----
> > From: "Michael Thomas" <thomin@bellsouth.net>
> > To: <vectorlist@synthcom.com>
> > Sent: Tuesday, April 09, 2002 9:51 PM
> > Subject: Re: VECTOR: WG 6100 GRY wire
> >
> > > The gray (grey?) wire attaches to the bottom aluminum plate of the
> > chassis,
> > > under
> > > the same screw as the wire coming from the spring that stretches along
the
> > > bottom
> > > of the tube. I would DEFINITELY re-connect it. As stated so many
times
> > > before
> > > on Vectorlist, grounds are very important.
> > >
> > > Michael
> > >
> > > ----- Original Message -----
> > > From: "LOUIS SRIANOMAI" <louisurfer@yahoo.com>
> > > To: <vectorlist@synthcom.com>
> > > Sent: Tuesday, April 09, 2002 4:31 PM
> > > Subject: Re: VECTOR: WG 6100 GRY wire
> > >
> > >
> > > > I just wired one of these, but I think it ties down to the chassis,
I
> > can
> > > take
> > > > a look tonight.
> > > >
> > > > L.
> > > >
> > > >
> > > > --- "Bachmann, Joe C" <joe.c.bachmann@xo.com> wrote:
> > > > >
> > > > > Where does the wire marked GRY next to the tube socket on neck
board
> > of
> > > a
> > > > > WG 6100 go to?
> > > > >
> > > > > Both mine have this broke off. Does this even make a difference?
> > > > >
> > > > > Thanks,
> > > > > Joe
> > > > >
> > > > >
> > > >
> > >
> >
> --------------------------------------------------------------------------
> > > -
> > > > > ** To UNSUBSCRIBE from vectorlist, send a message with
"UNSUBSCRIBE"
> > in
> > > the
> > > > > ** message body to vectorlist-request@synthcom.com. Please direct
> > other
> > > > > ** questions, comments, or problems to neil@synthcom.com.
> > > >
> > >
> >
> --------------------------------------------------------------------------
> > > -
> > > > > ** To UNSUBSCRIBE from vectorlist, send a message with
"UNSUBSCRIBE"
> > in
> > > the
> > > > > ** message body to vectorlist-request@synthcom.com. Please direct
> > other
> > > > > ** questions, comments, or problems to neil@synthcom.com.
> > > >
> > > >
> > > > __________________________________________________
> > > > Do You Yahoo!?
> > > > Yahoo! Tax Center - online filing with TurboTax
> > > > http://taxes.yahoo.com/
> > >
> >
> --------------------------------------------------------------------------
> > > -
> > > > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
in
> > > the
> > > > ** message body to vectorlist-request@synthcom.com. Please direct
other
> > > > ** questions, comments, or problems to neil@synthcom.com.
> > >
> >
> --------------------------------------------------------------------------
> > -
> > > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
in
> > the
> > > ** message body to vectorlist-request@synthcom.com. Please direct
other
> > > ** questions, comments, or problems to neil@synthcom.com.
> >
>
> --------------------------------------------------------------------------
-
> > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
> > ** message body to vectorlist-request@synthcom.com. Please direct other
> > ** questions, comments, or problems to neil@synthcom.com.
>
> --------------------------------------------------------------------------
-
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to neil@synthcom.com.

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Wed Apr 10 11:21:32 2002