Re: Bulk buy on Wintron flybacks

Hi,

I have heard folks in here talk about doing a bulk buy on these so many times
but I have never seen anything become of it. I think I read a post where John
Robertson was willing to do it if he could get some folks to prepay. I can use
4 -5 of these so Im very interested. Lets get this thing going .......who all
would be willing to do it?

Mark Capps

Michael Thomas wrote:

> Yes Joe, it is a ground. As a matter of fact it is the center tap to the
> 3-wire monitor power connection! I'm amazed anyone would cut this wire.
> That gray wire goes to pin 14 on the monitor's 15-pin main input connector
> (J100). It's the pin between the two violet wires on one end of the
> connector. After passing through the connector, it veers off with the two
> 25 volt power wires. It is also the center pin on this 3-pin connector.
> Once again, you would absolutely want to rework this one.
>
> Michael
>
> ----- Original Message -----
> From: "Joe Bachmann" <joe.bachmann@newmail.net>
> To: <vectorlist@synthcom.com>
> Sent: Wednesday, April 10, 2002 12:30 AM
> Subject: Re: VECTOR: WG 6100 GRY wire
>
> > Now I need to ask this: Is the wire marked GRY next to the large caps on
> the
> > deflection board also a ground?
> >
> > I have found on all thw WG 6100 parts I have that these wires have been
> chopped
> > (probably by ops.)
> >
> > Thanks much,
> > Joe
> >
> > Chris Starr wrote:
> >
> > > I can confirm, definitely a grounding wire. Bolts on to the aluminum
> chassis
> > > on one of the holes between the HV chassis box and the deflection board
> on
> > > the right. Probably will help reduce the jitters you mentioned.
> > >
> > > c-starr
> > >
> > > ----- Original Message -----
> > > From: "Michael Thomas" <thomin@bellsouth.net>
> > > To: <vectorlist@synthcom.com>
> > > Sent: Tuesday, April 09, 2002 9:51 PM
> > > Subject: Re: VECTOR: WG 6100 GRY wire
> > >
> > > > The gray (grey?) wire attaches to the bottom aluminum plate of the
> > > chassis,
> > > > under
> > > > the same screw as the wire coming from the spring that stretches along
> the
> > > > bottom
> > > > of the tube. I would DEFINITELY re-connect it. As stated so many
> times
> > > > before
> > > > on Vectorlist, grounds are very important.
> > > >
> > > > Michael
> > > >
> > > > ----- Original Message -----
> > > > From: "LOUIS SRIANOMAI" <louisurfer@yahoo.com>
> > > > To: <vectorlist@synthcom.com>
> > > > Sent: Tuesday, April 09, 2002 4:31 PM
> > > > Subject: Re: VECTOR: WG 6100 GRY wire
> > > >
> > > >
> > > > > I just wired one of these, but I think it ties down to the chassis,
> I
> > > can
> > > > take
> > > > > a look tonight.
> > > > >
> > > > > L.
> > > > >
> > > > >
> > > > > --- "Bachmann, Joe C" <joe.c.bachmann@xo.com> wrote:
> > > > > >
> > > > > > Where does the wire marked GRY next to the tube socket on neck
> board
> > > of
> > > > a
> > > > > > WG 6100 go to?
> > > > > >
> > > > > > Both mine have this broke off. Does this even make a difference?
> > > > > >
> > > > > > Thanks,
> > > > > > Joe
> > > > > >
> > > > > >
> > > > >
> > > >
> > >
> > --------------------------------------------------------------------------
> > > > -
> > > > > > ** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE"
> > > in
> > > > the
> > > > > > ** message body to vectorlist-request@synthcom.com. Please direct
> > > other
> > > > > > ** questions, comments, or problems to neil@synthcom.com.
> > > > >
> > > >
> > >
> > --------------------------------------------------------------------------
> > > > -
> > > > > > ** To UNSUBSCRIBE from vectorlist, send a message with
> "UNSUBSCRIBE"
> > > in
> > > > the
> > > > > > ** message body to vectorlist-request@synthcom.com. Please direct
> > > other
> > > > > > ** questions, comments, or problems to neil@synthcom.com.
> > > > >
> > > > >
> > > > > __________________________________________________
> > > > > Do You Yahoo!?
> > > > > Yahoo! Tax Center - online filing with TurboTax
> > > > > http://taxes.yahoo.com/
> > > >
> > >
> > --------------------------------------------------------------------------
> > > > -
> > > > > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
> in
> > > > the
> > > > > ** message body to vectorlist-request@synthcom.com. Please direct
> other
> > > > > ** questions, comments, or problems to neil@synthcom.com.
> > > >
> > >
> > --------------------------------------------------------------------------
> > > -
> > > > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE"
> in
> > > the
> > > > ** message body to vectorlist-request@synthcom.com. Please direct
> other
> > > > ** questions, comments, or problems to neil@synthcom.com.
> > >
> >
> > --------------------------------------------------------------------------
> -
> > > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
> the
> > > ** message body to vectorlist-request@synthcom.com. Please direct other
> > > ** questions, comments, or problems to neil@synthcom.com.
> >
> > --------------------------------------------------------------------------
> -
> > ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in
> the
> > ** message body to vectorlist-request@synthcom.com. Please direct other
> > ** questions, comments, or problems to neil@synthcom.com.
>
> ---------------------------------------------------------------------------
> ** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
> ** message body to vectorlist-request@synthcom.com. Please direct other
> ** questions, comments, or problems to neil@synthcom.com.

---------------------------------------------------------------------------
** To UNSUBSCRIBE from vectorlist, send a message with "UNSUBSCRIBE" in the
** message body to vectorlist-request@synthcom.com. Please direct other
** questions, comments, or problems to neil@synthcom.com.
Received on Thu Apr 11 12:34:57 2002